Skip to content

About

Lightest ESP32-based blimp controller with the works; 9-DoF, ToF altimetry, motor drivers, and Wi-Fi enabled camera streaming, all on a single 300mAh LiPo. >1hr of battery life.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Latest commit

 

History

6 Commits

Folders and files

NameName
Last commit message
Last commit date
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Falcon Core

Side-by-side images of the Falcon Core board

A custom standalone ESP32-S3 flight controller for an indoor autonomous blimp. Successor to Falcon Flight, redesigned from a Raspberry Pi Zero 2W HAT into a purpose-built 32×46mm 4-layer PCB.

Sponsored by PCBWay.

Specifications

  • MCU: ESP32-S3-WROOM-1 (N8R8/N16R8) — dual-core LX7, Wi-Fi, BLE, 8MB PSRAM
  • Camera: OV2640 via 24-pin 0.5mm FFC, 8-bit DVP interface
  • IMU: BMI270 (6-axis accel/gyro, I2C)
  • Magnetometer: MMC5633NJL (3-axis AMR, I2C, 1.62–3.6V)
  • ToF Sensor: VL53L5CX (I2C)
  • Motor Drivers: 4× DRV8212P bidirectional H-bridge
  • Battery Sensing: Internal ADC (GPIO7)
  • Status LED: Programmable red LED (GPIO48)
  • Board: 32×46mm, 4-layer, matte black solder mask
  • Weight: only 11 grams (excluding battery)

Power

  • Battery: BetaFPV 3.7V 300mAh 1S LiPo
  • Charging: TP4057 via USB-C (5.1kΩ CC pull-downs)
  • Motor Power: Direct battery feed to DRV8212P VM pins
  • Logic Isolation: BLM18PG221SN1D ferrite bead between battery and logic rail
  • Regulators (ME6211 LDOs, SOT-23-5):
    • 3.3V — ESP32-S3, sensors, VDDIO
    • 2.8V × 2 — OV2640 AVDD and DOVDD
    • 1.2V — OV2640 DVDD

GPIO Assignment

GPIO Function
1, 2 SCCB (camera I2C — SIOD, SIOC)
3 M2_IN1
4 M3_IN2
5 M3_IN1
6 M1_IN2
7 BAT_ADC (battery voltage sensing)
8, 18 Main I2C bus (SDA, SCL)
9, 10, 11, 12, 13, 14, 21, 40 OV2640 DVP data bus (D8, D7, D6, D2, D5, D3, D4, D9)
15 M4_IN1
16 M4_IN2
17 M2_IN2
19, 20 USB D−/D+
38 Camera PCLK
39 Camera XCLK
41 HREF
42 VSYNC
43, 44 UART0 debug
47 M1_IN1
48 Red LED (1kΩ to GND)

Camera PWDN tied to GND, RESETB tied to 3.3V.

I2C Bus

All sensors share the main I2C bus (GPIO8/18):

  • BMI270 (accel/gyro)
  • MMC5633NJL (magnetometer)
  • VL53L5CX (time-of-flight)

Camera SCCB runs on a separate bus (GPIO1/2).

Motor Layout

  • 2× horizontal forward-facing motors (thrust)
  • 1× downward-facing altitude motor (mounted below PCB on standoff)
  • 1× TBD

Firmware

Built with ESP-IDF. Custom PID stabilization (no ArduPilot). Communicates with a laptop over WebSocket for optical flow and AprilTag detection via OpenCV.

License

See LICENSE.

About

Lightest ESP32-based blimp controller with the works; 9-DoF, ToF altimetry, motor drivers, and Wi-Fi enabled camera streaming, all on a single 300mAh LiPo. >1hr of battery life.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages